🚚 Free Worldwide Shipping on All Orders!Shop Now
Commercial Power Rack
In Stock — Sydney Milperra Warehouse 🏋️ 11-Gauge 75×75mm Steel ⚖️ 1000kg Static Rating Westside Hole Spacing 🚚 Australia-Wide Dispatch
⚠️ Important: J-Hooks Not Included. This commercial power rack is sold without J-hooks. Sandwich J-hooks and other barbell hooks are available separately — see our recommended add-ons below. Safety spotter arms are also available as an add-on and strongly recommended for solo training.
The Commercial Power Rack from 24/7 Gym Equipment is a heavy-duty full gym cage built from 11-gauge 75×75×3mm steel uprights with an 3mm thick reinforced steel plate base — the same structural specification used in professional strength and conditioning facilities across Australia. With a 1000kg static weight rating, Westside hole spacing at bench height, laser-cut numbered positions and a 145kg frame weight, this Olympic power rack is engineered for heavy squats, bench press, overhead press and rack pulls in home garage gyms, PT studios and commercial gym fitouts across Sydney, Melbourne and Brisbane. Available in stock now with fast Australia-wide dispatch from our Milperra NSW warehouse.
1000KGStatic Weight Rating
145KGFrame Weight
75×75MMUpright Profile
18MMHole Diameter
The 4 Numbers That Separate Commercial from Budget Racks
75×75mm Upright profile — commercial standard. Budget racks use 50×50mm or smaller
11GA 3mm wall thickness — significantly stronger than 12–14 gauge budget alternatives
8MM Thick steel base plate reinforcement — eliminates rack lean and frame flex under maximum load
1000KG Static weight rating — tested and rated for elite powerlifting loads
75×75mm uprights vs 50×50mm — the difference you feel at 200kg+:
A 50×50mm upright (used on most budget and mid-range racks) has approximately 40% less cross-sectional steel than a 75×75mm upright at the same wall thickness. Under heavy loading — particularly during dynamic movements like squats where the bar oscillates — 50×50mm frames produce measurable flex and noise. The 75×75×3mm uprights on this commercial power rack stay completely rigid. Combined with the 8mm thick base plate reinforcement and 145kg frame weight, there is zero wobble at any load within the 1000kg rated capacity.
A 50×50mm upright (used on most budget and mid-range racks) has approximately 40% less cross-sectional steel than a 75×75mm upright at the same wall thickness. Under heavy loading — particularly during dynamic movements like squats where the bar oscillates — 50×50mm frames produce measurable flex and noise. The 75×75×3mm uprights on this commercial power rack stay completely rigid. Combined with the 8mm thick base plate reinforcement and 145kg frame weight, there is zero wobble at any load within the 1000kg rated capacity.
Attachments Included as Standard
33mm Straight Pull-Up Bar Included Standard 33mm diameter pull-up bar mounted at cage top — wide and narrow overhand grip positions for lat and upper back development
Multi-Grip Pull-Up Bar Included Multi-grip bar with neutral, wide and angled grip positions — chin-ups, neutral grip pull-ups and angled grip variations from a single overhead bar
Olympic Plate Storage Posts 4 posts included Four Olympic plate storage horns built into the rack frame — keeps plates organised, floor clear and adds ballast weight to improve rack stability
Adjustable Band Pegs 4 pegs included Four adjustable band pegs at base and upper positions — attach resistance bands to the bar for accommodating resistance training on squats, bench and deadlifts
⚠️
Not Included — Purchase Separately: Sandwich J-hooks · Safety spotter arms / flip-down safety bars · Olympic barbell · Weight plates · Adjustable bench. All accessories are available from our store — see recommended add-ons at the bottom of this page.
What Makes This a True Commercial Power Cage
🔩
11-Gauge 75×75×3mm Steel UprightsCommercial-grade heavy-duty upright profile — the structural specification used in professional strength facilities. Provides complete rigidity under 1000kg static loading with zero frame flex
⚖️
1000kg Static Weight RatingTested and rated for 1000kg static load — covers elite powerlifting squats, bench press and rack pulls at any level of competitive or recreational strength training
🔧
Westside Hole Spacing at Bench Height1-inch (25mm) hole spacing in the bench press zone — the Westside standard used on premium racks globally. Allows precise J-hook and safety arm positioning in 1-inch increments where it matters most during bench press
🔢
Laser-Cut Numbered PositionsEvery hole position is laser-cut and individually numbered — note your J-hook and safety arm height by number and return to it precisely every session without counting holes
🟫
3mm Thick Steel Base PlateReinforced 3mm thick steel plate at the base of each upright — distributes load across the full footprint and eliminates the upright lean that affects lighter-gauge racks under maximum loading
🔩
Bolt-Down Ready — Pre-Drilled BaseBase feet feature pre-drilled anchor holes for floor bolting — recommended for commercial facilities, kipping pull-ups and any training involving dynamic horizontal force application
💪
Dual Pull-Up Bars — Straight + Multi-GripTwo separate pull-up bars included: 33mm straight bar and a multi-grip bar with neutral, wide and angled positions — complete overhead pulling training without additional purchases
🎯
Power Rack with Band Pegs — 4 IncludedFour adjustable resistance band pegs at base and upper positions — enables accommodating resistance training on all major compound lifts without any additional attachment purchases
🏷️
Power Rack with Plate Storage — 4 PostsFour integrated Olympic plate storage posts — keeps plates at the rack, reduces trip hazards on the training floor and adds ballast weight for improved stability
✨
Matte Black Powder Coat — Double CoatedDouble powder-coat finish protects against rust, scratching and moisture — suited to Australian conditions including coastal humidity. Silicone spray recommended every few months for coastal suburb gyms
Technical Details
| Upright Profile | 75mm × 75mm × 3mm steel (11-gauge) |
| Base Plate Thickness | 3mm reinforced steel plate |
| Frame Weight | 145kg |
| Static Weight Rating | 1000kg |
| Hole Diameter | 18mm — standard pin diameter for compatible J-hooks and accessories |
| Hole Spacing | Westside spacing (25mm increments at bench height) · standard spacing elsewhere |
| Hole Numbering | Laser-cut numbered positions throughout |
| Dimensions (H×W×D) | 2,290mm × 1,322mm × 1,162mm |
| Pull-Up Bars | 33mm straight bar + multi-grip bar — both included |
| Plate Storage | 4× Olympic plate storage posts |
| Band Pegs | 4× adjustable band pegs |
| Finish | Double powder-coat matte black |
| Floor Anchoring | Pre-drilled base feet — bolt-down ready |
| J-Hooks | Not included — sold separately (sandwich J-hooks recommended) |
| Safety Arms | Not included — flip-down safety bars available separately |
| Barbell Compatibility | All 50mm Olympic barbells — standard 7ft bar recommended |
| Dispatch | In stock — daily dispatch from Milperra NSW · Click & Collect available |
What Is Westside Hole Spacing and Why Does It Matter?
Standard power racks use 50–75mm hole spacing throughout all uprights — meaning J-hook and safety arm height adjustments jump in 50mm increments. For squats this is fine. For bench press, where the difference between a safe unrack height and a failed rep catch height can be 25mm or less, standard spacing is too coarse. Westside hole spacing reduces the spacing to 25mm increments in the bench press zone — you can fine-tune your J-hook height to the nearest centimetre for perfect unracking position, and set safety arms at exactly the right catch height to protect your chest without limiting range of motion. This is a feature found on premium commercial racks — it is why bench pressers who train seriously specifically request Westside hole spacing when buying a rack.
Commercial Power Rack vs Budget Alternatives
| Specification | This Commercial Power Rack | Mid-Range Rack (~$500–800) | Budget Rack (~$200–400) |
|---|---|---|---|
| Upright Profile | 75×75×3mm (11-gauge) | 60×60mm or 50×50mm | 50×50mm or thinner |
| Base Reinforcement | 3mm thick steel plate | Standard footplate only | Thin footplate — flex risk |
| Static Weight Rating | 1000kg rated | 300–500kg typical | ~150–250kg |
| Hole Spacing | Westside (25mm at bench) | Standard 50mm only | Standard 50mm only |
| Hole Numbering | Laser-cut numbered | Sometimes numbered | Usually unnumbered |
| Pull-Up Bars | Straight + multi-grip (both included) | Usually 1 bar | 1 basic bar or none |
| Band Pegs | 4 adjustable pegs — included | Sometimes included | Rarely included |
| Plate Storage | 4 posts — included | Sometimes 2 posts | Rarely included |
| Floor Bolt Ready | Pre-drilled — bolt-down ready | Sometimes | Rarely |
30+ Exercises in One Commercial Power Cage
Barbell Back SquatSet sandwich J-hooks at shoulder height · safety arms below parallel · train squats to failure inside the full cage enclosure
Barbell Bench PressWestside hole spacing enables precise J-hook and flip-down safety arm positioning for safe solo bench press at heavy loads
Overhead Press (Standing)2,290mm height provides full overhead press clearance standing inside the cage — no ceiling contact risk
Rack Pull & Deadlift VariationSet safety arms at knee or mid-shin height for rack pulls — partial range overload for posterior chain strength
Pull-Up & Chin-UpStraight 33mm bar for standard overhand pull-ups · multi-grip bar for neutral, wide and angled grip variations
Banded Squat & Banded Bench4 adjustable band pegs enable accommodating resistance on squats, bench and deadlifts — builds speed-strength through the sticking point
Pin Press & Pause SquatUse safety arms as starting pins for dead-start pressing or bottom-position pause squats — specialty strength methods for powerlifting programming
Isometric Holds & Overcoming IsometricsPress or pull against the safety arms at specific joint angles for isometric strength development — a method used in elite strength and conditioning programmes
The Right Commercial Squat Rack For
- Serious home gym and garage gym owners — the 75×75mm uprights, 1000kg rating and 145kg frame weight deliver genuine commercial durability without the commercial facility price tag; a one-time purchase that will outlast cheaper alternatives
- PT studios requiring a high-capacity daily-use rack — the commercial steel specification, 1000kg rating and dual pull-up bars handle multiple clients per day without the frame wear, J-hook slippage or wobble common in lighter-gauge racks
- Commercial gym fitouts in Sydney, Melbourne and Brisbane — in-stock with daily dispatch from Milperra NSW; contact us for bulk pricing on multi-rack commercial gym fitout orders
- Powerlifters and strength athletes training heavy — Westside hole spacing, 1000kg rating and laser-cut numbered positions are the features competitive lifters specifically look for; this rack handles elite competition-level training loads
- Anyone upgrading from a budget or mid-range rack — if your current rack flexes, wobbles, has inadequate hole spacing or has J-hook slippage at heavy loads, this is the upgrade that eliminates all of those compromises permanently
Related Search Terms
Commercial Power Rack Power Cage Australia Commercial Squat Rack Heavy Duty Power Cage Full Gym Cage Olympic Power Rack 11-Gauge Steel Power Rack 75mm Upright Power Rack 18mm Hole Power Rack 1000kg Power Rack Westside Hole Spacing Rack Bolt-Down Power Rack Power Rack with Band Pegs Power Rack with Plate Storage Squat Rack with Spotter Arms In Stock Power Rack Australia Commercial Gym Fitout Sydney Premium Home Gym Equipment Professional Strength Training Cage Buy Power Rack Online Australia
Common Questions — Commercial Power Rack Australia
No — J-hooks are not included and must be purchased separately. We recommend sandwich J-hooks for this rack — the sandwich design clamps around the upright from both sides rather than inserting from one direction, which eliminates lateral movement under heavy loading. Standard pin-in J-hooks are also compatible with the upright hole pattern. See our recommended add-ons section for compatible J-hook options.
Westside hole spacing refers to 25mm (1-inch) hole increments in the bench press zone of the uprights — compared to the standard 50–75mm spacing used on budget racks throughout the full upright. The tighter spacing in the bench zone allows you to fine-tune your J-hook and safety arm height in 1-inch increments where precision matters most during bench press. For squats, 50mm increments are sufficient. For bench press — where the difference between a comfortable unrack and a shoulder-compromised setup can be 20–30mm — Westside spacing gives you the precision to get it exactly right every session.
The 1000kg static weight rating means the rack frame has been tested to support 1000kg of downward static load applied through the J-hook positions. This covers any realistic barbell training load — even elite powerlifters competing at 300–400kg total loading are well within the rated capacity. The rating is a static (non-moving) load test — dynamic impact loads during drops or sudden failures may vary, which is why safety arms and controlled lifting technique remain important regardless of rack rating.
Yes. The rack is 2,290mm tall — standard Australian 2.4m (2,400mm) garage ceilings provide 110mm of overhead clearance for pull-ups. The footprint is 1,322mm wide × 1,162mm deep. Plan your garage layout with at least 60–90cm of clearance on each side for safe barbell loading and movement around the rack. The double powder-coat finish handles the temperature variation and humidity of Australian garage environments — for coastal suburbs (Bondi, Coogee, Cronulla), apply silicone spray every few months to any exposed metal.
The 145kg frame weight provides significant standalone stability for standard barbell movements — squats, bench press and overhead press. Floor bolting is strongly recommended for commercial facilities, kipping pull-ups, toes-to-bar and any dynamic movements where sudden lateral force is applied. The base feet are pre-drilled for floor anchor bolts — use concrete anchors for slab floors or coach bolts for timber subfloors. Bolting adds no modification to the rack and can be undone if you relocate.
No — safety arms are not included and are sold separately. They are strongly recommended for anyone training solo. We carry flip-down safety bars that pivot out of the way for unracking and flip into position for the working set — faster than pin-in spotter arms for changing exercises. Pin-in safety arms are also compatible with the upright hole pattern. Contact us to confirm which safety arm attachment is in stock for this rack model.
The rack has a 1,322mm internal width between uprights. A standard 7ft (2,130mm) Olympic barbell fits comfortably — the sleeves extend beyond both uprights with clearance for collars. A 6ft (1,830mm) barbell also works for most movements. Do not use barbells shorter than 6ft — sleeve clearance from the uprights becomes insufficient when wide-diameter bumper plates are loaded. All 50mm Olympic barbells are compatible with the upright J-hook mounting position.
Yes — professional assembly and installation is available for Sydney Metro customers at an additional fee. Contact us with your suburb for a quote before ordering. For interstate customers, the rack ships with illustrated assembly instructions — two people and approximately 90–120 minutes are recommended for safe assembly of the 145kg frame. A socket wrench set speeds assembly significantly compared to the included hardware tools.
Yes — the rack is designed for future accessory expansion. The 18mm hole diameter and 75×75mm upright dimensions are compatible with a range of aftermarket accessories including cable pulley systems, lat pulldown attachments, dip bar handles, landmine bases and more. When purchasing third-party attachments, confirm they are specified for 18mm pins and 75×75mm uprights — some attachments use different pin diameters (25mm is common on American-standard racks) and will not fit correctly. Contact us for a list of confirmed-compatible accessories for this rack.
In Stock — Fast Dispatch from Milperra NSW
Sydney Metro1–3 business days
Melbourne & Brisbane2–5 business days
Adelaide, Perth & Regional3–7 business days
Click & Collect — Milperra NSW 2214
10/202 Milperra Road, Milperra NSW 2214 · Mon–Fri 9am–5pm · Sat 9am–1pm. Commercial gym fitout pricing available — contact us for multi-rack bulk orders for Sydney, Melbourne and Brisbane facilities.
Recommended Add-Ons
10/202 Milperra Road, Milperra NSW 2214 · Mon–Fri 9am–5pm · Sat 9am–1pm. Commercial gym fitout pricing available — contact us for multi-rack bulk orders for Sydney, Melbourne and Brisbane facilities.
Complete Your Commercial Strength Station
🏋️ Olympic Barbells → 🛋️ Adjustable Benches → ⚫ Bumper Plates → 🏗️ More Power Racks →
Commercial Power Rack Delivery Areas — Australia:
Sydney (NSW) · Parramatta · Bankstown · Liverpool · Penrith · Blacktown · Campbelltown · Bondi · Chatswood · Castle Hill · Northern Beaches · Manly · North Sydney · Mosman · Inner West · Sutherland Shire · Lower North Shore · Eastern Suburbs · Ryde · Central Coast · Newcastle · Wollongong · Melbourne (VIC) · Richmond · Brunswick · Essendon · Frankston · Dandenong · Geelong · Ballarat · Brisbane (QLD) · Fortitude Valley · Gold Coast · Sunshine Coast · Toowoomba · Cairns · Adelaide (SA) · Perth (WA) · Canberra (ACT) · Hobart (TAS) · Darwin (NT)
Sydney (NSW) · Parramatta · Bankstown · Liverpool · Penrith · Blacktown · Campbelltown · Bondi · Chatswood · Castle Hill · Northern Beaches · Manly · North Sydney · Mosman · Inner West · Sutherland Shire · Lower North Shore · Eastern Suburbs · Ryde · Central Coast · Newcastle · Wollongong · Melbourne (VIC) · Richmond · Brunswick · Essendon · Frankston · Dandenong · Geelong · Ballarat · Brisbane (QLD) · Fortitude Valley · Gold Coast · Sunshine Coast · Toowoomba · Cairns · Adelaide (SA) · Perth (WA) · Canberra (ACT) · Hobart (TAS) · Darwin (NT)
$208.01
Original: $693.36
-70%Commercial Power Rack—
$693.36
$208.01More Images
Commercial Power Rack
In Stock — Sydney Milperra Warehouse 🏋️ 11-Gauge 75×75mm Steel ⚖️ 1000kg Static Rating Westside Hole Spacing 🚚 Australia-Wide Dispatch
⚠️ Important: J-Hooks Not Included. This commercial power rack is sold without J-hooks. Sandwich J-hooks and other barbell hooks are available separately — see our recommended add-ons below. Safety spotter arms are also available as an add-on and strongly recommended for solo training.
The Commercial Power Rack from 24/7 Gym Equipment is a heavy-duty full gym cage built from 11-gauge 75×75×3mm steel uprights with an 3mm thick reinforced steel plate base — the same structural specification used in professional strength and conditioning facilities across Australia. With a 1000kg static weight rating, Westside hole spacing at bench height, laser-cut numbered positions and a 145kg frame weight, this Olympic power rack is engineered for heavy squats, bench press, overhead press and rack pulls in home garage gyms, PT studios and commercial gym fitouts across Sydney, Melbourne and Brisbane. Available in stock now with fast Australia-wide dispatch from our Milperra NSW warehouse.
1000KGStatic Weight Rating
145KGFrame Weight
75×75MMUpright Profile
18MMHole Diameter
The 4 Numbers That Separate Commercial from Budget Racks
75×75mm Upright profile — commercial standard. Budget racks use 50×50mm or smaller
11GA 3mm wall thickness — significantly stronger than 12–14 gauge budget alternatives
8MM Thick steel base plate reinforcement — eliminates rack lean and frame flex under maximum load
1000KG Static weight rating — tested and rated for elite powerlifting loads
75×75mm uprights vs 50×50mm — the difference you feel at 200kg+:
A 50×50mm upright (used on most budget and mid-range racks) has approximately 40% less cross-sectional steel than a 75×75mm upright at the same wall thickness. Under heavy loading — particularly during dynamic movements like squats where the bar oscillates — 50×50mm frames produce measurable flex and noise. The 75×75×3mm uprights on this commercial power rack stay completely rigid. Combined with the 8mm thick base plate reinforcement and 145kg frame weight, there is zero wobble at any load within the 1000kg rated capacity.
A 50×50mm upright (used on most budget and mid-range racks) has approximately 40% less cross-sectional steel than a 75×75mm upright at the same wall thickness. Under heavy loading — particularly during dynamic movements like squats where the bar oscillates — 50×50mm frames produce measurable flex and noise. The 75×75×3mm uprights on this commercial power rack stay completely rigid. Combined with the 8mm thick base plate reinforcement and 145kg frame weight, there is zero wobble at any load within the 1000kg rated capacity.
Attachments Included as Standard
33mm Straight Pull-Up Bar Included Standard 33mm diameter pull-up bar mounted at cage top — wide and narrow overhand grip positions for lat and upper back development
Multi-Grip Pull-Up Bar Included Multi-grip bar with neutral, wide and angled grip positions — chin-ups, neutral grip pull-ups and angled grip variations from a single overhead bar
Olympic Plate Storage Posts 4 posts included Four Olympic plate storage horns built into the rack frame — keeps plates organised, floor clear and adds ballast weight to improve rack stability
Adjustable Band Pegs 4 pegs included Four adjustable band pegs at base and upper positions — attach resistance bands to the bar for accommodating resistance training on squats, bench and deadlifts
⚠️
Not Included — Purchase Separately: Sandwich J-hooks · Safety spotter arms / flip-down safety bars · Olympic barbell · Weight plates · Adjustable bench. All accessories are available from our store — see recommended add-ons at the bottom of this page.
What Makes This a True Commercial Power Cage
🔩
11-Gauge 75×75×3mm Steel UprightsCommercial-grade heavy-duty upright profile — the structural specification used in professional strength facilities. Provides complete rigidity under 1000kg static loading with zero frame flex
⚖️
1000kg Static Weight RatingTested and rated for 1000kg static load — covers elite powerlifting squats, bench press and rack pulls at any level of competitive or recreational strength training
🔧
Westside Hole Spacing at Bench Height1-inch (25mm) hole spacing in the bench press zone — the Westside standard used on premium racks globally. Allows precise J-hook and safety arm positioning in 1-inch increments where it matters most during bench press
🔢
Laser-Cut Numbered PositionsEvery hole position is laser-cut and individually numbered — note your J-hook and safety arm height by number and return to it precisely every session without counting holes
🟫
3mm Thick Steel Base PlateReinforced 3mm thick steel plate at the base of each upright — distributes load across the full footprint and eliminates the upright lean that affects lighter-gauge racks under maximum loading
🔩
Bolt-Down Ready — Pre-Drilled BaseBase feet feature pre-drilled anchor holes for floor bolting — recommended for commercial facilities, kipping pull-ups and any training involving dynamic horizontal force application
💪
Dual Pull-Up Bars — Straight + Multi-GripTwo separate pull-up bars included: 33mm straight bar and a multi-grip bar with neutral, wide and angled positions — complete overhead pulling training without additional purchases
🎯
Power Rack with Band Pegs — 4 IncludedFour adjustable resistance band pegs at base and upper positions — enables accommodating resistance training on all major compound lifts without any additional attachment purchases
🏷️
Power Rack with Plate Storage — 4 PostsFour integrated Olympic plate storage posts — keeps plates at the rack, reduces trip hazards on the training floor and adds ballast weight for improved stability
✨
Matte Black Powder Coat — Double CoatedDouble powder-coat finish protects against rust, scratching and moisture — suited to Australian conditions including coastal humidity. Silicone spray recommended every few months for coastal suburb gyms
Technical Details
| Upright Profile | 75mm × 75mm × 3mm steel (11-gauge) |
| Base Plate Thickness | 3mm reinforced steel plate |
| Frame Weight | 145kg |
| Static Weight Rating | 1000kg |
| Hole Diameter | 18mm — standard pin diameter for compatible J-hooks and accessories |
| Hole Spacing | Westside spacing (25mm increments at bench height) · standard spacing elsewhere |
| Hole Numbering | Laser-cut numbered positions throughout |
| Dimensions (H×W×D) | 2,290mm × 1,322mm × 1,162mm |
| Pull-Up Bars | 33mm straight bar + multi-grip bar — both included |
| Plate Storage | 4× Olympic plate storage posts |
| Band Pegs | 4× adjustable band pegs |
| Finish | Double powder-coat matte black |
| Floor Anchoring | Pre-drilled base feet — bolt-down ready |
| J-Hooks | Not included — sold separately (sandwich J-hooks recommended) |
| Safety Arms | Not included — flip-down safety bars available separately |
| Barbell Compatibility | All 50mm Olympic barbells — standard 7ft bar recommended |
| Dispatch | In stock — daily dispatch from Milperra NSW · Click & Collect available |
What Is Westside Hole Spacing and Why Does It Matter?
Standard power racks use 50–75mm hole spacing throughout all uprights — meaning J-hook and safety arm height adjustments jump in 50mm increments. For squats this is fine. For bench press, where the difference between a safe unrack height and a failed rep catch height can be 25mm or less, standard spacing is too coarse. Westside hole spacing reduces the spacing to 25mm increments in the bench press zone — you can fine-tune your J-hook height to the nearest centimetre for perfect unracking position, and set safety arms at exactly the right catch height to protect your chest without limiting range of motion. This is a feature found on premium commercial racks — it is why bench pressers who train seriously specifically request Westside hole spacing when buying a rack.
Commercial Power Rack vs Budget Alternatives
| Specification | This Commercial Power Rack | Mid-Range Rack (~$500–800) | Budget Rack (~$200–400) |
|---|---|---|---|
| Upright Profile | 75×75×3mm (11-gauge) | 60×60mm or 50×50mm | 50×50mm or thinner |
| Base Reinforcement | 3mm thick steel plate | Standard footplate only | Thin footplate — flex risk |
| Static Weight Rating | 1000kg rated | 300–500kg typical | ~150–250kg |
| Hole Spacing | Westside (25mm at bench) | Standard 50mm only | Standard 50mm only |
| Hole Numbering | Laser-cut numbered | Sometimes numbered | Usually unnumbered |
| Pull-Up Bars | Straight + multi-grip (both included) | Usually 1 bar | 1 basic bar or none |
| Band Pegs | 4 adjustable pegs — included | Sometimes included | Rarely included |
| Plate Storage | 4 posts — included | Sometimes 2 posts | Rarely included |
| Floor Bolt Ready | Pre-drilled — bolt-down ready | Sometimes | Rarely |
30+ Exercises in One Commercial Power Cage
Barbell Back SquatSet sandwich J-hooks at shoulder height · safety arms below parallel · train squats to failure inside the full cage enclosure
Barbell Bench PressWestside hole spacing enables precise J-hook and flip-down safety arm positioning for safe solo bench press at heavy loads
Overhead Press (Standing)2,290mm height provides full overhead press clearance standing inside the cage — no ceiling contact risk
Rack Pull & Deadlift VariationSet safety arms at knee or mid-shin height for rack pulls — partial range overload for posterior chain strength
Pull-Up & Chin-UpStraight 33mm bar for standard overhand pull-ups · multi-grip bar for neutral, wide and angled grip variations
Banded Squat & Banded Bench4 adjustable band pegs enable accommodating resistance on squats, bench and deadlifts — builds speed-strength through the sticking point
Pin Press & Pause SquatUse safety arms as starting pins for dead-start pressing or bottom-position pause squats — specialty strength methods for powerlifting programming
Isometric Holds & Overcoming IsometricsPress or pull against the safety arms at specific joint angles for isometric strength development — a method used in elite strength and conditioning programmes
The Right Commercial Squat Rack For
- Serious home gym and garage gym owners — the 75×75mm uprights, 1000kg rating and 145kg frame weight deliver genuine commercial durability without the commercial facility price tag; a one-time purchase that will outlast cheaper alternatives
- PT studios requiring a high-capacity daily-use rack — the commercial steel specification, 1000kg rating and dual pull-up bars handle multiple clients per day without the frame wear, J-hook slippage or wobble common in lighter-gauge racks
- Commercial gym fitouts in Sydney, Melbourne and Brisbane — in-stock with daily dispatch from Milperra NSW; contact us for bulk pricing on multi-rack commercial gym fitout orders
- Powerlifters and strength athletes training heavy — Westside hole spacing, 1000kg rating and laser-cut numbered positions are the features competitive lifters specifically look for; this rack handles elite competition-level training loads
- Anyone upgrading from a budget or mid-range rack — if your current rack flexes, wobbles, has inadequate hole spacing or has J-hook slippage at heavy loads, this is the upgrade that eliminates all of those compromises permanently
Related Search Terms
Commercial Power Rack Power Cage Australia Commercial Squat Rack Heavy Duty Power Cage Full Gym Cage Olympic Power Rack 11-Gauge Steel Power Rack 75mm Upright Power Rack 18mm Hole Power Rack 1000kg Power Rack Westside Hole Spacing Rack Bolt-Down Power Rack Power Rack with Band Pegs Power Rack with Plate Storage Squat Rack with Spotter Arms In Stock Power Rack Australia Commercial Gym Fitout Sydney Premium Home Gym Equipment Professional Strength Training Cage Buy Power Rack Online Australia
Common Questions — Commercial Power Rack Australia
No — J-hooks are not included and must be purchased separately. We recommend sandwich J-hooks for this rack — the sandwich design clamps around the upright from both sides rather than inserting from one direction, which eliminates lateral movement under heavy loading. Standard pin-in J-hooks are also compatible with the upright hole pattern. See our recommended add-ons section for compatible J-hook options.
Westside hole spacing refers to 25mm (1-inch) hole increments in the bench press zone of the uprights — compared to the standard 50–75mm spacing used on budget racks throughout the full upright. The tighter spacing in the bench zone allows you to fine-tune your J-hook and safety arm height in 1-inch increments where precision matters most during bench press. For squats, 50mm increments are sufficient. For bench press — where the difference between a comfortable unrack and a shoulder-compromised setup can be 20–30mm — Westside spacing gives you the precision to get it exactly right every session.
The 1000kg static weight rating means the rack frame has been tested to support 1000kg of downward static load applied through the J-hook positions. This covers any realistic barbell training load — even elite powerlifters competing at 300–400kg total loading are well within the rated capacity. The rating is a static (non-moving) load test — dynamic impact loads during drops or sudden failures may vary, which is why safety arms and controlled lifting technique remain important regardless of rack rating.
Yes. The rack is 2,290mm tall — standard Australian 2.4m (2,400mm) garage ceilings provide 110mm of overhead clearance for pull-ups. The footprint is 1,322mm wide × 1,162mm deep. Plan your garage layout with at least 60–90cm of clearance on each side for safe barbell loading and movement around the rack. The double powder-coat finish handles the temperature variation and humidity of Australian garage environments — for coastal suburbs (Bondi, Coogee, Cronulla), apply silicone spray every few months to any exposed metal.
The 145kg frame weight provides significant standalone stability for standard barbell movements — squats, bench press and overhead press. Floor bolting is strongly recommended for commercial facilities, kipping pull-ups, toes-to-bar and any dynamic movements where sudden lateral force is applied. The base feet are pre-drilled for floor anchor bolts — use concrete anchors for slab floors or coach bolts for timber subfloors. Bolting adds no modification to the rack and can be undone if you relocate.
No — safety arms are not included and are sold separately. They are strongly recommended for anyone training solo. We carry flip-down safety bars that pivot out of the way for unracking and flip into position for the working set — faster than pin-in spotter arms for changing exercises. Pin-in safety arms are also compatible with the upright hole pattern. Contact us to confirm which safety arm attachment is in stock for this rack model.
The rack has a 1,322mm internal width between uprights. A standard 7ft (2,130mm) Olympic barbell fits comfortably — the sleeves extend beyond both uprights with clearance for collars. A 6ft (1,830mm) barbell also works for most movements. Do not use barbells shorter than 6ft — sleeve clearance from the uprights becomes insufficient when wide-diameter bumper plates are loaded. All 50mm Olympic barbells are compatible with the upright J-hook mounting position.
Yes — professional assembly and installation is available for Sydney Metro customers at an additional fee. Contact us with your suburb for a quote before ordering. For interstate customers, the rack ships with illustrated assembly instructions — two people and approximately 90–120 minutes are recommended for safe assembly of the 145kg frame. A socket wrench set speeds assembly significantly compared to the included hardware tools.
Yes — the rack is designed for future accessory expansion. The 18mm hole diameter and 75×75mm upright dimensions are compatible with a range of aftermarket accessories including cable pulley systems, lat pulldown attachments, dip bar handles, landmine bases and more. When purchasing third-party attachments, confirm they are specified for 18mm pins and 75×75mm uprights — some attachments use different pin diameters (25mm is common on American-standard racks) and will not fit correctly. Contact us for a list of confirmed-compatible accessories for this rack.
In Stock — Fast Dispatch from Milperra NSW
Sydney Metro1–3 business days
Melbourne & Brisbane2–5 business days
Adelaide, Perth & Regional3–7 business days
Click & Collect — Milperra NSW 2214
10/202 Milperra Road, Milperra NSW 2214 · Mon–Fri 9am–5pm · Sat 9am–1pm. Commercial gym fitout pricing available — contact us for multi-rack bulk orders for Sydney, Melbourne and Brisbane facilities.
Recommended Add-Ons
10/202 Milperra Road, Milperra NSW 2214 · Mon–Fri 9am–5pm · Sat 9am–1pm. Commercial gym fitout pricing available — contact us for multi-rack bulk orders for Sydney, Melbourne and Brisbane facilities.
Complete Your Commercial Strength Station
🏋️ Olympic Barbells → 🛋️ Adjustable Benches → ⚫ Bumper Plates → 🏗️ More Power Racks →
Commercial Power Rack Delivery Areas — Australia:
Sydney (NSW) · Parramatta · Bankstown · Liverpool · Penrith · Blacktown · Campbelltown · Bondi · Chatswood · Castle Hill · Northern Beaches · Manly · North Sydney · Mosman · Inner West · Sutherland Shire · Lower North Shore · Eastern Suburbs · Ryde · Central Coast · Newcastle · Wollongong · Melbourne (VIC) · Richmond · Brunswick · Essendon · Frankston · Dandenong · Geelong · Ballarat · Brisbane (QLD) · Fortitude Valley · Gold Coast · Sunshine Coast · Toowoomba · Cairns · Adelaide (SA) · Perth (WA) · Canberra (ACT) · Hobart (TAS) · Darwin (NT)
Sydney (NSW) · Parramatta · Bankstown · Liverpool · Penrith · Blacktown · Campbelltown · Bondi · Chatswood · Castle Hill · Northern Beaches · Manly · North Sydney · Mosman · Inner West · Sutherland Shire · Lower North Shore · Eastern Suburbs · Ryde · Central Coast · Newcastle · Wollongong · Melbourne (VIC) · Richmond · Brunswick · Essendon · Frankston · Dandenong · Geelong · Ballarat · Brisbane (QLD) · Fortitude Valley · Gold Coast · Sunshine Coast · Toowoomba · Cairns · Adelaide (SA) · Perth (WA) · Canberra (ACT) · Hobart (TAS) · Darwin (NT)
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
In Stock — Sydney Milperra Warehouse 🏋️ 11-Gauge 75×75mm Steel ⚖️ 1000kg Static Rating Westside Hole Spacing 🚚 Australia-Wide Dispatch
⚠️ Important: J-Hooks Not Included. This commercial power rack is sold without J-hooks. Sandwich J-hooks and other barbell hooks are available separately — see our recommended add-ons below. Safety spotter arms are also available as an add-on and strongly recommended for solo training.
The Commercial Power Rack from 24/7 Gym Equipment is a heavy-duty full gym cage built from 11-gauge 75×75×3mm steel uprights with an 3mm thick reinforced steel plate base — the same structural specification used in professional strength and conditioning facilities across Australia. With a 1000kg static weight rating, Westside hole spacing at bench height, laser-cut numbered positions and a 145kg frame weight, this Olympic power rack is engineered for heavy squats, bench press, overhead press and rack pulls in home garage gyms, PT studios and commercial gym fitouts across Sydney, Melbourne and Brisbane. Available in stock now with fast Australia-wide dispatch from our Milperra NSW warehouse.
1000KGStatic Weight Rating
145KGFrame Weight
75×75MMUpright Profile
18MMHole Diameter
The 4 Numbers That Separate Commercial from Budget Racks
75×75mm Upright profile — commercial standard. Budget racks use 50×50mm or smaller
11GA 3mm wall thickness — significantly stronger than 12–14 gauge budget alternatives
8MM Thick steel base plate reinforcement — eliminates rack lean and frame flex under maximum load
1000KG Static weight rating — tested and rated for elite powerlifting loads
75×75mm uprights vs 50×50mm — the difference you feel at 200kg+:
A 50×50mm upright (used on most budget and mid-range racks) has approximately 40% less cross-sectional steel than a 75×75mm upright at the same wall thickness. Under heavy loading — particularly during dynamic movements like squats where the bar oscillates — 50×50mm frames produce measurable flex and noise. The 75×75×3mm uprights on this commercial power rack stay completely rigid. Combined with the 8mm thick base plate reinforcement and 145kg frame weight, there is zero wobble at any load within the 1000kg rated capacity.
A 50×50mm upright (used on most budget and mid-range racks) has approximately 40% less cross-sectional steel than a 75×75mm upright at the same wall thickness. Under heavy loading — particularly during dynamic movements like squats where the bar oscillates — 50×50mm frames produce measurable flex and noise. The 75×75×3mm uprights on this commercial power rack stay completely rigid. Combined with the 8mm thick base plate reinforcement and 145kg frame weight, there is zero wobble at any load within the 1000kg rated capacity.
Attachments Included as Standard
33mm Straight Pull-Up Bar Included Standard 33mm diameter pull-up bar mounted at cage top — wide and narrow overhand grip positions for lat and upper back development
Multi-Grip Pull-Up Bar Included Multi-grip bar with neutral, wide and angled grip positions — chin-ups, neutral grip pull-ups and angled grip variations from a single overhead bar
Olympic Plate Storage Posts 4 posts included Four Olympic plate storage horns built into the rack frame — keeps plates organised, floor clear and adds ballast weight to improve rack stability
Adjustable Band Pegs 4 pegs included Four adjustable band pegs at base and upper positions — attach resistance bands to the bar for accommodating resistance training on squats, bench and deadlifts
⚠️
Not Included — Purchase Separately: Sandwich J-hooks · Safety spotter arms / flip-down safety bars · Olympic barbell · Weight plates · Adjustable bench. All accessories are available from our store — see recommended add-ons at the bottom of this page.
What Makes This a True Commercial Power Cage
🔩
11-Gauge 75×75×3mm Steel UprightsCommercial-grade heavy-duty upright profile — the structural specification used in professional strength facilities. Provides complete rigidity under 1000kg static loading with zero frame flex
⚖️
1000kg Static Weight RatingTested and rated for 1000kg static load — covers elite powerlifting squats, bench press and rack pulls at any level of competitive or recreational strength training
🔧
Westside Hole Spacing at Bench Height1-inch (25mm) hole spacing in the bench press zone — the Westside standard used on premium racks globally. Allows precise J-hook and safety arm positioning in 1-inch increments where it matters most during bench press
🔢
Laser-Cut Numbered PositionsEvery hole position is laser-cut and individually numbered — note your J-hook and safety arm height by number and return to it precisely every session without counting holes
🟫
3mm Thick Steel Base PlateReinforced 3mm thick steel plate at the base of each upright — distributes load across the full footprint and eliminates the upright lean that affects lighter-gauge racks under maximum loading
🔩
Bolt-Down Ready — Pre-Drilled BaseBase feet feature pre-drilled anchor holes for floor bolting — recommended for commercial facilities, kipping pull-ups and any training involving dynamic horizontal force application
💪
Dual Pull-Up Bars — Straight + Multi-GripTwo separate pull-up bars included: 33mm straight bar and a multi-grip bar with neutral, wide and angled positions — complete overhead pulling training without additional purchases
🎯
Power Rack with Band Pegs — 4 IncludedFour adjustable resistance band pegs at base and upper positions — enables accommodating resistance training on all major compound lifts without any additional attachment purchases
🏷️
Power Rack with Plate Storage — 4 PostsFour integrated Olympic plate storage posts — keeps plates at the rack, reduces trip hazards on the training floor and adds ballast weight for improved stability
✨
Matte Black Powder Coat — Double CoatedDouble powder-coat finish protects against rust, scratching and moisture — suited to Australian conditions including coastal humidity. Silicone spray recommended every few months for coastal suburb gyms
Technical Details
| Upright Profile | 75mm × 75mm × 3mm steel (11-gauge) |
| Base Plate Thickness | 3mm reinforced steel plate |
| Frame Weight | 145kg |
| Static Weight Rating | 1000kg |
| Hole Diameter | 18mm — standard pin diameter for compatible J-hooks and accessories |
| Hole Spacing | Westside spacing (25mm increments at bench height) · standard spacing elsewhere |
| Hole Numbering | Laser-cut numbered positions throughout |
| Dimensions (H×W×D) | 2,290mm × 1,322mm × 1,162mm |
| Pull-Up Bars | 33mm straight bar + multi-grip bar — both included |
| Plate Storage | 4× Olympic plate storage posts |
| Band Pegs | 4× adjustable band pegs |
| Finish | Double powder-coat matte black |
| Floor Anchoring | Pre-drilled base feet — bolt-down ready |
| J-Hooks | Not included — sold separately (sandwich J-hooks recommended) |
| Safety Arms | Not included — flip-down safety bars available separately |
| Barbell Compatibility | All 50mm Olympic barbells — standard 7ft bar recommended |
| Dispatch | In stock — daily dispatch from Milperra NSW · Click & Collect available |
What Is Westside Hole Spacing and Why Does It Matter?
Standard power racks use 50–75mm hole spacing throughout all uprights — meaning J-hook and safety arm height adjustments jump in 50mm increments. For squats this is fine. For bench press, where the difference between a safe unrack height and a failed rep catch height can be 25mm or less, standard spacing is too coarse. Westside hole spacing reduces the spacing to 25mm increments in the bench press zone — you can fine-tune your J-hook height to the nearest centimetre for perfect unracking position, and set safety arms at exactly the right catch height to protect your chest without limiting range of motion. This is a feature found on premium commercial racks — it is why bench pressers who train seriously specifically request Westside hole spacing when buying a rack.
Commercial Power Rack vs Budget Alternatives
| Specification | This Commercial Power Rack | Mid-Range Rack (~$500–800) | Budget Rack (~$200–400) |
|---|---|---|---|
| Upright Profile | 75×75×3mm (11-gauge) | 60×60mm or 50×50mm | 50×50mm or thinner |
| Base Reinforcement | 3mm thick steel plate | Standard footplate only | Thin footplate — flex risk |
| Static Weight Rating | 1000kg rated | 300–500kg typical | ~150–250kg |
| Hole Spacing | Westside (25mm at bench) | Standard 50mm only | Standard 50mm only |
| Hole Numbering | Laser-cut numbered | Sometimes numbered | Usually unnumbered |
| Pull-Up Bars | Straight + multi-grip (both included) | Usually 1 bar | 1 basic bar or none |
| Band Pegs | 4 adjustable pegs — included | Sometimes included | Rarely included |
| Plate Storage | 4 posts — included | Sometimes 2 posts | Rarely included |
| Floor Bolt Ready | Pre-drilled — bolt-down ready | Sometimes | Rarely |
30+ Exercises in One Commercial Power Cage
Barbell Back SquatSet sandwich J-hooks at shoulder height · safety arms below parallel · train squats to failure inside the full cage enclosure
Barbell Bench PressWestside hole spacing enables precise J-hook and flip-down safety arm positioning for safe solo bench press at heavy loads
Overhead Press (Standing)2,290mm height provides full overhead press clearance standing inside the cage — no ceiling contact risk
Rack Pull & Deadlift VariationSet safety arms at knee or mid-shin height for rack pulls — partial range overload for posterior chain strength
Pull-Up & Chin-UpStraight 33mm bar for standard overhand pull-ups · multi-grip bar for neutral, wide and angled grip variations
Banded Squat & Banded Bench4 adjustable band pegs enable accommodating resistance on squats, bench and deadlifts — builds speed-strength through the sticking point
Pin Press & Pause SquatUse safety arms as starting pins for dead-start pressing or bottom-position pause squats — specialty strength methods for powerlifting programming
Isometric Holds & Overcoming IsometricsPress or pull against the safety arms at specific joint angles for isometric strength development — a method used in elite strength and conditioning programmes
The Right Commercial Squat Rack For
- Serious home gym and garage gym owners — the 75×75mm uprights, 1000kg rating and 145kg frame weight deliver genuine commercial durability without the commercial facility price tag; a one-time purchase that will outlast cheaper alternatives
- PT studios requiring a high-capacity daily-use rack — the commercial steel specification, 1000kg rating and dual pull-up bars handle multiple clients per day without the frame wear, J-hook slippage or wobble common in lighter-gauge racks
- Commercial gym fitouts in Sydney, Melbourne and Brisbane — in-stock with daily dispatch from Milperra NSW; contact us for bulk pricing on multi-rack commercial gym fitout orders
- Powerlifters and strength athletes training heavy — Westside hole spacing, 1000kg rating and laser-cut numbered positions are the features competitive lifters specifically look for; this rack handles elite competition-level training loads
- Anyone upgrading from a budget or mid-range rack — if your current rack flexes, wobbles, has inadequate hole spacing or has J-hook slippage at heavy loads, this is the upgrade that eliminates all of those compromises permanently
Related Search Terms
Commercial Power Rack Power Cage Australia Commercial Squat Rack Heavy Duty Power Cage Full Gym Cage Olympic Power Rack 11-Gauge Steel Power Rack 75mm Upright Power Rack 18mm Hole Power Rack 1000kg Power Rack Westside Hole Spacing Rack Bolt-Down Power Rack Power Rack with Band Pegs Power Rack with Plate Storage Squat Rack with Spotter Arms In Stock Power Rack Australia Commercial Gym Fitout Sydney Premium Home Gym Equipment Professional Strength Training Cage Buy Power Rack Online Australia
Common Questions — Commercial Power Rack Australia
No — J-hooks are not included and must be purchased separately. We recommend sandwich J-hooks for this rack — the sandwich design clamps around the upright from both sides rather than inserting from one direction, which eliminates lateral movement under heavy loading. Standard pin-in J-hooks are also compatible with the upright hole pattern. See our recommended add-ons section for compatible J-hook options.
Westside hole spacing refers to 25mm (1-inch) hole increments in the bench press zone of the uprights — compared to the standard 50–75mm spacing used on budget racks throughout the full upright. The tighter spacing in the bench zone allows you to fine-tune your J-hook and safety arm height in 1-inch increments where precision matters most during bench press. For squats, 50mm increments are sufficient. For bench press — where the difference between a comfortable unrack and a shoulder-compromised setup can be 20–30mm — Westside spacing gives you the precision to get it exactly right every session.
The 1000kg static weight rating means the rack frame has been tested to support 1000kg of downward static load applied through the J-hook positions. This covers any realistic barbell training load — even elite powerlifters competing at 300–400kg total loading are well within the rated capacity. The rating is a static (non-moving) load test — dynamic impact loads during drops or sudden failures may vary, which is why safety arms and controlled lifting technique remain important regardless of rack rating.
Yes. The rack is 2,290mm tall — standard Australian 2.4m (2,400mm) garage ceilings provide 110mm of overhead clearance for pull-ups. The footprint is 1,322mm wide × 1,162mm deep. Plan your garage layout with at least 60–90cm of clearance on each side for safe barbell loading and movement around the rack. The double powder-coat finish handles the temperature variation and humidity of Australian garage environments — for coastal suburbs (Bondi, Coogee, Cronulla), apply silicone spray every few months to any exposed metal.
The 145kg frame weight provides significant standalone stability for standard barbell movements — squats, bench press and overhead press. Floor bolting is strongly recommended for commercial facilities, kipping pull-ups, toes-to-bar and any dynamic movements where sudden lateral force is applied. The base feet are pre-drilled for floor anchor bolts — use concrete anchors for slab floors or coach bolts for timber subfloors. Bolting adds no modification to the rack and can be undone if you relocate.
No — safety arms are not included and are sold separately. They are strongly recommended for anyone training solo. We carry flip-down safety bars that pivot out of the way for unracking and flip into position for the working set — faster than pin-in spotter arms for changing exercises. Pin-in safety arms are also compatible with the upright hole pattern. Contact us to confirm which safety arm attachment is in stock for this rack model.
The rack has a 1,322mm internal width between uprights. A standard 7ft (2,130mm) Olympic barbell fits comfortably — the sleeves extend beyond both uprights with clearance for collars. A 6ft (1,830mm) barbell also works for most movements. Do not use barbells shorter than 6ft — sleeve clearance from the uprights becomes insufficient when wide-diameter bumper plates are loaded. All 50mm Olympic barbells are compatible with the upright J-hook mounting position.
Yes — professional assembly and installation is available for Sydney Metro customers at an additional fee. Contact us with your suburb for a quote before ordering. For interstate customers, the rack ships with illustrated assembly instructions — two people and approximately 90–120 minutes are recommended for safe assembly of the 145kg frame. A socket wrench set speeds assembly significantly compared to the included hardware tools.
Yes — the rack is designed for future accessory expansion. The 18mm hole diameter and 75×75mm upright dimensions are compatible with a range of aftermarket accessories including cable pulley systems, lat pulldown attachments, dip bar handles, landmine bases and more. When purchasing third-party attachments, confirm they are specified for 18mm pins and 75×75mm uprights — some attachments use different pin diameters (25mm is common on American-standard racks) and will not fit correctly. Contact us for a list of confirmed-compatible accessories for this rack.
In Stock — Fast Dispatch from Milperra NSW
Sydney Metro1–3 business days
Melbourne & Brisbane2–5 business days
Adelaide, Perth & Regional3–7 business days
Click & Collect — Milperra NSW 2214
10/202 Milperra Road, Milperra NSW 2214 · Mon–Fri 9am–5pm · Sat 9am–1pm. Commercial gym fitout pricing available — contact us for multi-rack bulk orders for Sydney, Melbourne and Brisbane facilities.
Recommended Add-Ons
10/202 Milperra Road, Milperra NSW 2214 · Mon–Fri 9am–5pm · Sat 9am–1pm. Commercial gym fitout pricing available — contact us for multi-rack bulk orders for Sydney, Melbourne and Brisbane facilities.
Complete Your Commercial Strength Station
🏋️ Olympic Barbells → 🛋️ Adjustable Benches → ⚫ Bumper Plates → 🏗️ More Power Racks →
Commercial Power Rack Delivery Areas — Australia:
Sydney (NSW) · Parramatta · Bankstown · Liverpool · Penrith · Blacktown · Campbelltown · Bondi · Chatswood · Castle Hill · Northern Beaches · Manly · North Sydney · Mosman · Inner West · Sutherland Shire · Lower North Shore · Eastern Suburbs · Ryde · Central Coast · Newcastle · Wollongong · Melbourne (VIC) · Richmond · Brunswick · Essendon · Frankston · Dandenong · Geelong · Ballarat · Brisbane (QLD) · Fortitude Valley · Gold Coast · Sunshine Coast · Toowoomba · Cairns · Adelaide (SA) · Perth (WA) · Canberra (ACT) · Hobart (TAS) · Darwin (NT)
Sydney (NSW) · Parramatta · Bankstown · Liverpool · Penrith · Blacktown · Campbelltown · Bondi · Chatswood · Castle Hill · Northern Beaches · Manly · North Sydney · Mosman · Inner West · Sutherland Shire · Lower North Shore · Eastern Suburbs · Ryde · Central Coast · Newcastle · Wollongong · Melbourne (VIC) · Richmond · Brunswick · Essendon · Frankston · Dandenong · Geelong · Ballarat · Brisbane (QLD) · Fortitude Valley · Gold Coast · Sunshine Coast · Toowoomba · Cairns · Adelaide (SA) · Perth (WA) · Canberra (ACT) · Hobart (TAS) · Darwin (NT)
